Thứ Sáu, 6 tháng 2, 2009

CCNA 1 - Module 10 (v4.0)

Download file pdf nhe.

http://pthuynh.5vn.com/Module10.pdf

CCNA 1 - Module 11

1. Users in the network are experiencing slow response time when doing file transfers to a remote server. What command could be issued to determine if the router has experienced any input or output errors?
• show running-config
• show startup-config
• show interfaces
• show ip route
• show version
• show memory


2. Refer to the exhibit. A technician applies the configuration in the exhibit to a clean router. To verify the configuration, the technician issues the show running-config command in the CLI session with the router. What lines should the technician expect to see in the router output from the show running-config command?
• enable password classline console 0password ccna
• enable secret ciscoenable password classline console 0password ccna
• enable secret 5 $1$v0/3$QyQWmJyT7zCa/yaBRasJm0enable password classline console 0password ccna
• enable secret ciscoenable password 7 14141E0A1F17line console 0password 7 020507550A
• enable secret 5 $1$v0/3$QyQWmJyT7zCa/yaBRasJm0enable password 7 14141E0A1F17line console 0password 7 020507550A

3. Refer to the exhibit. A network administrator on HostA has problems accessing the FTP server. Layer three connectivity testing was successful from HostA to the S1 interface of RouterB. Which set of commands will allow the network administrator to telnet to RouterB and run debug commands?
• RouterB(config)# enable secret class
RouterB(config)# line vty 0 4
RouterB(config-if)# login
• RouterB(config)# enable secret class
RouterB(config)# line vty 0 2
RouterB(config-vty)# password cisco
RouterB(config-vty)# login
• RouterB(config)# enable secret class
RouterB(config)# line vty 0
RouterB(config-line)# password cisco
RouterB(config-line)# login
• RouterB(config)# enable secret class
RouterB(config)# line aux 0
RouterB(config-line)# password cisco
RouterB(config-line)# login
• RouterB(config)# enable secret class
RouterB(config)# line aux 0
RouterB(config-vty)# password cisco
RouterB(config-vty)# login
4. Refer to the exhibit. The output is shown for the show ip route command executed on Router A. What does the IP address 192.168.2.2 represent?
• Gateway for the 192.168.1.0 network
• Gateway for the 192.168.3.0 network
• IP assigned to the serial port on Router A
• IP assigned to the serial port on Router B

5. What command is used to change the default router name to Fontana?
• Router# name Fontana
• Router# hostname Fontana
• Router(config)# name Fontana
• Router(config)# hostname Fontana

6. The serial connection shown in the graphic needs to be configured. Which configuration commands must be made on the Sydney router to establish connectivity with the Melbourne site? (Choose three.)
• Sydney(config-if)# ip address 201.100.53.2 255.255.255.0
• Sydney(config-if)# no shutdown
• Sydney(config-if)# ip address 201.100.53.1 255.255.255.224
• Sydney(config-if)# clock rate 56000
• Sydney(config-if)# ip host Melbourne 201.100.53.2
7. Refer to the exhibit. What additional command is required to allow remote access to this switch?
• NA-SW1(config-if)# no shutdown
• NA-SW1(config)# enable password password
• NA-SW1(config)# ip default-gateway address
• NA-SW1(config-if)# description description
8. When network services fail, which port is most often used to access a router for management purposes?
AUX
Ethernet
• Console
Telnet
SSH

9. A network administrator needs to keep the user ID, password, and session contents private when establishing remote CLI connectivity with a router to manage it. Which access method should be chosen?
• Telnet
• Console
• AUX
• SSH
welcome to www.ccna-4.blogspot.com
10. In a Cisco router, when do changes made to the running-configuration take effect?
• after a system restart
• as the commands are entered
• when logging off the system
• when the configuration is saved to the startup-configuration
11. Refer to the exhibit. Which names correctly identify the CLI mode represented by the prompt for Switch-East4#? (Choose two.)
• line configuration mode
• user executive mode
• global configuration mode
• privileged executive mode
• interface configuration mode
• enable mode

12. Which three terms correctly define the forms of help available within the Cisco IOS? (Choose three.)
• hot keys
• context-check
• context-sensitive
• structured check
• command override
• command syntax check
13. Which combination of keys would be used at the CLI prompt to interrupt a ping or traceroute process?
• Ctrl-C
• Ctrl-P
• Ctrl-R
• Ctrl-Shift-6
• Ctrl-Z

14. Refer to the exhibit. What command will place the router into the correct mode to configure an appropriate interface to connect to a LAN?
• UBAMA# configure terminal
• UBAMA(config)# line vty 0 4
• UBAMA(config)# line console 0
• UBAMA(config)# interface Serial 0/0/0
• UBAMA(config)# interface FastEthernet 0/1

15. On a Cisco router, which interface would be used to make the initial configuration?
• Console Port

16. Refer to the exhibit. A student is responsible for the IP addressing, configuration and connectivity testing of the network shown in the graphic. A ping from host B to host C results in a destination unreachable but a ping from host B to host A was successful. What two reasons could account for this failure based on the graphic and partial router output for the Dallas router? (Choose two.)
• The host A is turned off.
• The Fa0/0 interface on Dallas is shutdown.
• The LAN cable is disconnected from host B.
• The S0/0/1 IP address of Dallas is improperly configured.
• The Fa0/0 interface on Dallas is in a different subnet than host B.

CCNA1 FINAL 100% (Updated Jan 14 - 2009).

1 A PC can not connect to any remote websites, ping its default gateway, or ping a printer that is functioning properly on the local network segment. Which action will verify that the TCP/IP stack is functioning correctly on this PC?

Use the ipconfig /all command at the host�s command prompt.
X Use the ping 127.0.0.1 command at the command prompt.
Use the traceroute command at the command prompt to identify any failures on the path to the gateway.
Use FTP to check for connectivity to remote sites.
Download a troubleshooting tool from the PC manufacturer's website.

2 Refer to the exhibit. Which set of devices contains only intermediary devices?

X A, B, D, G
A, B, E, F
C, D, G, I
G, H, I, J


3 Refer to the exhibit. When computer A sends a frame to computer D, what computers receive the frame?

X only computer D
only computer A and computer D
only computer B, computer C, and computer D
all computers


4 Which password is automatically encrypted when it is created?

vty
aux
console
X enable secret
enable password


5 Which three statements characterize the transport layer protocols? (Choose three.)

X TCP and UDP port numbers are used by application layer protocols.
TCP uses port numbers to provide reliable transportation of IP packets.
UDP uses windowing and acknowledgments for reliable transfer of data.
X TCP uses windowing and sequencing to provide reliable transfer of data.
X TCP is a connection-oriented protocol. UDP is a connectionless protocol.


6 Which type of media is immune to EMI and RFI? (Choose two.)

10 Base-T
10 Base-2
10 Base-5
X 100 Base-FX
100 Base TX
X 1000 Base LX


7 Refer to the exhibit. A technician is working on a network problem that requires verification of the router LAN interface. What address should be pinged from this host to confirm that the router interface is operational?

127.0.0.1
192.168.64.196
X 192.168.254.1
192.168.254.9
192.168.254.254


8 Refer to the exhibit. The diagram represents the process of sending email between clients. Select the list below that correctly identifies the component or protocol used at each numbered stage of the diagram.

1.MUA 2.MDA 3.MTA 4.SMTP 5.MTA 6.POP 7.MDA 8.MUA
1.MUA 2.POP 3.MDA 4.SMTP 5.MTA 6.MDA 7.SMTP 8.MUA
1.MUA 2.POP 3.SMTP 4.MDA 5.MTA 6.SMTP 7.POP 8.MUA
1.MDA 2.SMTP 3.MTA 4.SMTP 5.MTA 6.MUA 7.POP 8.MDA
X 1.MUA 2.SMTP 3.MTA 4.SMTP 5.MTA 6.MDA 7.POP 8.MUA


9 Refer to the exhibit. What function does router RT_A need to provide to allow Internet access for hosts in this network?

X address translation
DHCP services
ftpd
web server


10 Refer to the exhibit. The network containing router B is experiencing problems. A network associate has isolated the issue in this network to router B? What action can be preformed to correct the network issue?

issue the ip address command on interface FastEthernet 0/0
X issue the no shutdown command on interface FastEthernet 0/1
issue the clock rate command on interface Serial 0/0/0
issue the description command on interface Serial 0/0/1


11 Which three IPv4 addresses represent a broadcast for a subnet? (Choose three.)

X 172.16.4.63 /26
172.16.4.129 /26
X 172.16.4.191 /26
172.16.4.51 /27
X 172.16.4.95 /27
172.16.4.221 /27


12 What are three characteristics of CSMA/CD? (Choose three.)

Devices can be configured with a higher transmission priority.
A jam signal indicates that the collision has cleared and the media is not busy.
X A device listens and waits until the media is not busy before transmitting.
The device with the electronic token is the only one that can transmit after a collision.
X All of the devices on a segment see data that passes on the network medium.
X After detecting a collision, hosts can attempt to resume transmission after a random time delay has expired.


13 In a Cisco IOS device, where is the startup-configuration file stored?

Flash
X NVRAM
RAM
ROM


14 A routing issue has occurred in you internetwork. Which of the following type of devices should be examined to isolate this error?

access point
host
hub
X router
switch


15 Which OSI layer protocol does IP rely on to determine whether packets have been lost and to request retransmission?

application
presentation
session
X transport


16 Due to a security violation, the router passwords must be changed. What information can be learned from the following configuration entries? (Choose two.)

Router(config)# line vty 0 3
Router(config-line)# password c13c0
Router(config-line)# login

The entries specify three Telnet lines for remote access.
X The entries specify four Telnet lines for remote access.
The entries set the console and Telnet password to "c13c0".
Telnet access will be denied because the Telnet configuration is incomplete.
X Access will be permitted for Telnet using "c13c0" as the password.


17 Which prompt represents the appropriate mode used for the copy running-config startup-config command ?

Switch-6J>
X Switch-6J#
Switch-6J(config)#
Switch-6J(config-if)#
Switch-6J(config-line)#


18 Which combination of network id and subnet mask correctly identifies all IP addresses from 172.16.128.0 through 172.16.159.255?

172.16.128.0 255.255.255.224
172.16.128.0 255.255.0.0
172.16.128.0 255.255.192.0
X 172.16.128.0 255.255.224.0
172.16.128.0 255.255.255.192


19 When must a router serial interface be configured with the clock rate command?

when the interface is functioning as a DTE device
when the interface timers have been cleared
when the connected DTE device is shut down
X when the interface is functioning as a DCE device


20 When connectionless protocols are implemented at the lower layers of the OSI model, what are usually used to acknowledge the data receipt and request the retransmission of missing data?

connectionless acknowledgements
X upper-layer connection-oriented protocols
Network layer IP protocols
Transport layer UDP protocols


21 A technician is asked to secure the privileged EXEC mode of a switch by requiring a password. Which type of password would require this login and be considered the most secure?

console
enable
X enable secret
VTY


22 Refer to the exhibit. What is required on host A for a network technician to create the initial configuration on RouterA?

a FTP client
a telnet client
X a terminal emulation program
a web browser


23 Refer to the exhibit. A network administrator remotely accesses the CLI of RouterB from PC1. Which two statements are true about the application layer protocol that is used to make this connection? (Choose two.)

The data is encrypted.
X The connection type is called a VTY session.
A server process is running on PC1.
A GET request is sent to RouterB.
X The application name is the same for the service, protocol, and client.


24 The Layer 4 header contains which type of information to aid in the delivery of data?

X service port number
host logical address
device physical address
virtual connection identifier


25 Refer to the exhibit. What two facts can be determined about the exhibited topology? (Choose two.)

X A single broadcast domain is present
Two logical address ranges are required.
Three broadcast domains are shown.
Four networks are needed.
X Five collision domains exist.


26 Refer to the exhibit. A network technician is trying to determine the correct IP address configuration for Host A. What is a valid configuration for Host A?

IP address: 192.168.100.19; Subnet Mask: 255.255.255.248; Default Gateway: 192.16.1.2
X IP address: 192.168.100.20; Subnet Mask: 255.255.255.240; Default Gateway: 192.168.100.17
IP address: 192.168.100.21; Subnet Mask: 255.255.255.248; Default Gateway: 192.168.100.18
IP address: 192.168.100.22; Subnet Mask: 255.255.255.240; Default Gateway: 10.1.1.5
IP address: 192.168.100.30; Subnet Mask: 255.255.255.240; Default Gateway: 192.168.1.1
IP address: 192.168.100.31; Subnet Mask: 255.255.255.240; Default Gateway: 192.168.100.18


27 Refer to the exhibit. Cable 1 and cable 2 have the ends wired for specific physical layer requirements. The table lists each segment by number and the cable which has been installed by the network technician between the network components on that segment. From the data given, which segments have the correct cable installed? (Choose three.)

X segment1
segment2
X segment3
X segment4
segment5


28 What is true regarding network layer addressing? (Choose three.)

uses a flat structure
prevent broadcasts
X heirarchical
X uniquely identifies each host
48 bits in length
X contains a network portion


29 Refer to the exhibit. A router, whose table is shown, receives a packet that is destined for 192.168.1.4. How will router treat the packet?

The packet will be dropped.
The packet will be forwarded via FastEthernet 0/0.
X The packet will be forwarded to the destination host.
The packet will be forwarded to the 192.168.1.3 next-hop address.


30 Refer to the exhibit. Which two statements describe the information that is represented in the header? (Choose two.)

This is a server response.
The UDP protocol is being used.
X The destination port indicates a Telnet session.
X The return segment will contain a source port of 23.
The next session originated from the client of this session will use the source port number 13358.


31 Refer to the exhibit. What is the correct destination socket number for a web page request from Host A to the web server?

00-08-a3-b6-ce-46
X 198.133.219.25:80
http://www.cisco.com
C 198.133.219.0/24 is directly connected, FastEthernet0/0


32 During the encapsulation process, which identifiers are added at the transport layer?

two networks routing the packets
X two applications communicating the data
two hosts at either end of the communication
two nodes on the local network exchanging the frame


33 Refer to the exhibit. A student has wired each end of a CAT 5e cable as shown. What is the result? (Choose two.)

The cable is unusable and must be rewired.
The cable is suitable for use as a Gigabit Ethernet straight-through.
X The cable is suitable for use as a Fast Ethernet crossover.
The cable is suitable for use as a rollover cable.
The cable is suitable for use as a Gigabit Ethernet crossover.
X The cable is suitable for use between two 100 Mbps Auto-MDIX capable switches.


34 Refer to the exhibit. Assume all devices are using default configurations. How many subnets are required to address the topology that is shown?

1
X 3
4
5
7


35 Refer to the exhibit. On the basis of the IP configuration that is shown, what is the reason that Host A and Host B are unable to communicate outside the local network?

Host A was assigned a network address.
Host B was assigned a multicast address.
Host A and Host B belong to different networks.
X The gateway address was assigned a broadcast address.


36 Refer to the exhibit. Each media link is labeled. What type of cable should be used to connect the different devices?

Connection 1 - rollover cable
Connection 2 - straight-through cable
Connection 3 - crossover cable

Connection 1 - crossover cable
Connection 2 - rollover cable
Connection 3 - crossover cable

Connection 1 - straight-through cable
Connection 2 - crossover cable
Connection 3 - crossover cable

X Connection 1 - straight-through cable
Connection 2 - crossover cable
Connection 3 - straight-through cable


Connection 1 - crossover cable
Connection 2 - straight-through cable
Connection 3 - crossover cable


37 Refer to the exhibit. What does the IP address 192.168.33.2 represent?

The host's default gateway.
The host's IP address.
X The host's primary domain name server.
The IP address of the website resolver1.mooki.local.
The IP address of the host's homepage.


38 Refer to the exhibit. What two facts can be determined from the information that is given? (Choose two.)

This exchange is part of the three-way handshake.
The source port indicates that a Telnet session has been initiated.
The data is flowing from server to client.
X The destination port indicates that an HTTP session has been initiated.
X The data listed is associated with the transport layer.
The source port does not support communication with the destination port that is listed.


39 Which of the following are the address ranges of the private IP addresses? (Choose three.)

X 10.0.0.0 to 10.255.255.255
200.100.50.0 to 200.100.25.255
150.150.0.0 to 150.150.255.255
X 172.16.0.0 to 172.31.255.255
X 192.168.0.0 to 192.168.255.255
127.16.0.0 to 127.31.255.255


40 Which two functions of the OSI model occur at layer two? (Choose two.)

X physical addressing
encoding
routing
cabling
X media access control


41 Which range of port numbers are reserved for services that are commonly used by applications that run on servers?

0 to 255
X 0 to 1023
1024 to 49151
49152 to 65535


42 As network administrator, what is the subnet mask that allows 510 hosts given the IP address 172.30.0.0?

255.255.0.0
255.255.248.0
255.255.252.0
X 255.255.254.0
255.255.255.0
255.255.255.128


43 Refer to the exhibit. The tracert command is initiated from PC1 to the destination PC4. Which device will send a response to the initial packet from PC1?

X London
Paris
Athens
Ankara
PC4


44 Refer to the exhibit. Host A is transmitting data to host B. What addresses will host A use to for the destination IP and MAC addresses in this communication?

Destination MAC: BBBB:BBBB:BBBB Destination IP: 172.22.0.62
Destination MAC: DDDD:DDDD:DDDD Destination IP: 172.22.0.75
Destination MAC: EEEE:EEEE:EEEE Destination IP: 172.22.0.62
Destination MAC: BBBB:BBBB:BBBB Destination IP: 172.22.0.75
X Destination MAC: EEEE:EEEE:EEEE Destination IP: 172.22.0.75
Destination MAC: DDDD:DDDD:DDDD Destination IP: 172.22.0.94


45 Refer to the exhibit. Which logical topology best describes the exhibited network?

star
ring
point-to-point
X multiaccess
mesh


46 Examine the graphic with current configurations. Host A in the Clerical offices failed and was replaced. Although a ping to 127.0.0.1 was successful, the replacement computer can not access the company network. What is the likely cause of the problem?

IP address incorrectly entered
network cables unplugged
X subnet mask incorrectly entered
network card failure


47 Refer to the exhibit. With the router running NAT, what IP addresses can be applied to the computer to allow access to the Internet? (Choose three.)

192.168.18.38
192.168.18.48
X 192.168.18.49
X 192.168.18.52
X 192.168.18.59
192.168.18.63


48 Refer to the exhibit. What three statements are true about the IP configuration that is shown? (Choose three.)

X The address that is assigned to the computer represents private addressing.
X The computer is unable to communicate outside of the local network.
The network of this computer can have 126 hosts.
X The prefix of the computer address is /27.
The IP address that is assigned to the computer is routable on the Internet.
The IP address that is assigned to the computer is a broadcast address.


49 Refer to the exhibit. Host A attempts to establish a TCP/IP session with host C. During this attempt, a frame was captured with the source MAC address 0050.7320.D632 and the destination MAC address 0030.8517.44C4. The packet inside the captured frame has an IP source address 192.168.7.5, and the destination IP address is 192.168.219.24. At which point in the network was this packet captured?

leaving host A
leaving ATL
X leaving Dallas
leaving NYC


50 Which of the following OSI layers offers reliable, connection-oriented data communication services?

application
presentation
session
Xtransport
network

Chủ Nhật, 11 tháng 1, 2009

CCNA 1 - Module 9 (v4.0)

1
In the graphic, Host A has reached 50% completion in sending a 1 KB Ethernet frame to Host D when Host B wishes to transmit its own frame to Host C. What must Host B do?

Host B can transmit immediately since it is connected on its own cable segment.
Host B must wait to receive a CSMA transmission from the hub, to signal its turn.
Host B must send a request signal to Host A by transmitting an interframe gap.
**Host B must wait until it is certain that Host A has completed sending its frame.



2
Ethernet operates at which layers of the OSI model? (Choose two.)

Network layer
Transport layer
**Physical layer
Application layer
Session layer
**Data-link layer



3
Which of the following describe interframe spacing? (Choose two.)

**the minimum interval, measured in bit-times, that any station must wait before sending another frame
the maximum interval, measured in bit-times, that any station must wait before sending another frame
the 96-bit payload padding inserted into a frame to achieve a legal frame size
the 96-bit frame padding transmitted between frames to achieve proper synchronization
**the time allowed for slow stations to process a frame and prepare for the next frame
the maximum interval within which a station must send another frame to avoid being considered unreachable



4
What three primary functions does data link layer encapsulation provide? (Choose three.)

**addressing
**error detection
**frame delimiting
port identification
path determination
IP address resolution



5
When a collision occurs in a network using CSMA/CD, how do hosts with data to transmit respond after the backoff period has expired?

**The hosts return to a listen-before-transmit mode. <--- The hosts creating the collision have priority to send data. The hosts creating the collision retransmit the last 16 frames. The hosts extend their delay period to allow for rapid transmission. 6 What are three functions of the upper data link sublayer in the OSI model? (Choose three.) recognizes streams of bits **identifies the network layer protocol **makes the connection with the upper layers identifies the source and destination applications **insulates network layer protocols from changes in physical equipment determines the source of a transmission when multiple devices are transmitting 7 What does the IEEE 802.2 standard represent in Ethernet technologies? MAC sublayer Physical layer **Logical Link Control sublayer Network layer 8 Why do hosts on an Ethernet segment that experience a collision use a random delay before attempting to transmit a frame? A random delay is used to ensure a collision-free link. A random delay value for each device is assigned by the manufacturer. A standard delay value could not be agreed upon among networking device vendors. **A random delay helps prevent the stations from experiencing another collision during the transmission. 9 Refer to the exhibit. Which option correctly matches the frame field type with the contents that frame field includes? header field - preamble and stop frame **data field - network layer packet data field - physical addressing trailer field - FCS and SoF


10
Host A has an IP address of 172.16.225.93 and a mask of 255.255.248.0. Host A needs to communicate with a new host whose IP is 172.16.231.78. Host A performs the ANDing operation on the destination address. What two things will occur? (Choose two.)

Host A will change the destination IP to the IP of the nearest router and forward the packet.
Host A will broadcast an ARP request for the MAC of its default gateway.
A result of 172.16.225.0 will be obtained.
**Host A will broadcast an ARP request for the MAC of the destination host.
A result of 172.16.224.0 will be obtained.
**A result of 172.16.225.255 will be obtained.



11
Which of the following is a drawback of the CSMA/CD access method?

**Collisions can decrease network performance.
It is more complex than non-deterministic protocols.
Deterministic media access protocols slow network performance.
CSMA/CD LAN technologies are only available at slower speeds than other LAN technologies.



12
Ethernet operates at which layer of the TCP/IP network model?

application
physical
transport
internet
data link
**network access



13
What is the primary purpose of ARP?

translate URLs to IP addresses
**resolve IPv4 addresses to MAC addresses
provide dynamic IP configuration to network devices
convert internal private addresses to external public addresses



14
Refer to the exhibit. The switch and workstation are administratively configured for full-duplex operation. Which statement accurately reflects the operation of this link?

**No collisions will occur on this link.
Only one of the devices can transmit at a time.
The switch will have priority for transmitting data.
The devices will default back to half duplex if excessive collisions occur.



15
Refer to the exhibit. Host_A is attempting to contact Server_B. Which statements correctly describe the addressing Host_A will generate in the process? (Choose two.)

A packet with the destination IP of Router_B.
A frame with the destination MAC address of Switch_A.
A packet with the destination IP of Router_A.
**A frame with the destination MAC address of Router_A.
**A packet with the destination IP of Server_B.
A frame with the destination MAC address of Server_B.

16
Which statements correctly describe MAC addresses? (Choose three.)

dynamically assigned
**copied into RAM during system startup
layer 3 address
**contains a 3 byte OUI
**6 bytes long
32 bits long



17
Which two features make switches preferable to hubs in Ethernet-based networks? (Choose two.)

reduction in cross-talk
**minimizing of collisions
support for UTP cabling
division into broadcast domains
**increase in the throughput of communications



18
What are the two most commonly used media types in Ethernet networks today? (Choose two.)

coaxial thicknet
**copper UTP
coaxial thinnet
**optical fiber
shielded twisted pair



19
Convert the binary number 10111010 into its hexadecimal equivalent. Select the correct answer from the list below.

85
90
**BA
A1
B3
1C



20
After an Ethernet collision, when the backoff algorithm is invoked, which device has priority to transmit data?

the device involved in the collision with the lowest MAC address
the device involved in the collision with the lowest IP address
**any device in the collision domain whose backoff timer expires first
those that began transmitting at the same time

CCNA 1 - Module 8 (v4.0)

1
Which type of cable run is most often associated with fiber-optic cable?
Xbackbone cable
horizontal cable
patch cable
work area cable

2
In most business LANs, which connector is used with twisted-pair networking cable?
BNC
RJ-11
**RJ-45
Type F

3
When is a straight-through cable used in a network?
when connecting a router through the console port
when connecting one switch to another switch
**when connecting a host to a switch
when connecting a router to another router

4
With the use of unshielded twisted-pair copper wire in a network, what causes crosstalk within the cable pairs?
**the magnetic field around the adjacent pairs of wire
the use of braided wire to shield the adjacent wire pairs
the reflection of the electrical wave back from the far end of the cable
the collision caused by two nodes trying to use the media simultaneously

5
Which OSI layer is responsible for binary transmission, cable specification, and physical aspects of network communication?
Presentation
Transport
Data Link
**Physical

6
An installed fiber run can be checked for faults, integrity, and the performance of the media by using what device?
light injector
**OTDR
TDR
multimeter

7
XYZ Company is installing new cable runs on their data network. What two types of cable would most commonly be used for new runs? (Choose two.)
**coax
Cat4 UTP
Cat5 UTP
**Cat6 UTP
STP

8
What is a possible effect of improperly applying a connector to a network cable?
Data will be forwarded to the wrong node.
**Data transmitted through that cable may experience signal loss.
An improper signaling method will be implemented for data transmitted on that cable.
The encoding method for data sent on that cable will change to compensate for the improper connection.

9
What are three measures of data transfer? (Choose three.)
goodput
**frequency
amplitude
**throughput
crosstalk
**bandwidth

10


Refer to the exhibit. Which type of Category 5 cable is used to make an Ethernet connection between Host A and Host B?
coax cable
rollover cable
**crossover cable
straight-through cable

11
In LAN installations where potential electrical hazards or electromagnetic interference may be present, what type of media is recommended for backbone cabling?
coax
**fiber
Cat5e UTP
Cat6 UTP
STP

12
Which fiber connector supports full duplex Ethernet?
kolmas


13
Which method of signal transmission uses radio waves to carry signals?
electrical
optical
**wireless
acoustic

14
Which characteristics describe fiber optic cable? (Choose two.)
**It is not affected by EMI or RFI.
Each pair of cables is wrapped in metallic foil.
It combines the technique of cancellation, shielding and twisting to protect data.
It has a maximum speed of 100 Mbps.
**It is the most expensive type of LAN cabling.

15
Which of the following is a characteristic of single-mode fiber-optic cable?
**generally uses LEDs as the light source
relatively larger core with multiple light paths
less expensive than multimode
generally uses lasers as the light source



16
What is considered a benefit of wireless as a media choice?
**more host mobility
lower security risks
reduced susceptibility to interference
less impact of the surroundings on the effective coverage area

17
What characteristic of UTP cable helps reduce the effects of interference?
the metal braiding in the shielding
the reflective cladding around core
**the twisting of the wires in the cable
the insulating material in the outer jacket

18
What is a primary role of the Physical layer in transmitting data on the network?
**create the signals that represent the bits in each frame on to the media
provide physical addressing to the devices
determine the path packets take through the network
control data access to the media

CCNA 1 - Module 7 (v4.0)

1
Which options are properties of contention-based media access for a shared media? (Choose three.)
**non-deterministic
**less overhead
one station transmits at a time
**collisions exist
devices must wait their turn
token passing

2
What is a primary purpose of encapsulating packets into frames?
provide routes across the internetwork
format the data for presentation to the user
**facilitate the entry and exit of data on media
identify the services to which transported data is associated

3
Refer to the exhibit. How many unique CRC calculations will take place as traffic routes from the PC to the laptop?
1
**2
4
8

4
What is true concerning physical and logical topologies?
The logical topology is always the same as the physical topology.
Physical topologies are concerned with how a network transfers frames.
Physical signal paths are defined by Data Link layer protocols.
**Logical topologies consist of virtual connections between nodes.

5
Refer to the exhibit. Assuming that the network in the exhibit is converged meaning the routing tables and ARP tables are complete, which MAC address will Host A place in the destination address field of Ethernet frames destined for www.server?
00-1c-41-ab-c0-00
**00-0c-85-cf-65-c0
00-0c-85-cf-65-c1
00-12-3f-32-05-af

6
What are three characteristics of valid Ethernet Layer 2 addresses? (Choose three.)
**They are 48 binary bits in length.
They are considered physical addresses.
**They are generally represented in hexadecimal format.
They consist of four eight-bit octets of binary numbers.
They are used to determine the data path through the network.
**They must be changed when an Ethernet device is added or moved within the network.

7
Refer to the exhibit. A frame is being sent from the PC to the laptop. Which source MAC and IP addresses will be included in the frame as it leaves RouterB? (Choose two.)
source MAC - PC
source MAC - S0/0 on RouterA
**source MAC - Fa0/1 on RouterB
**source IP - PC
source IP - S0/0 on RouterA
source IP - Fa0/1 of RouterB

8
What determines the method of media access control? (Choose two.)
network layer addressing
**media sharing
application processes
**logical topology
intermediary device function

9
What is the purpose of the preamble in an Ethernet frame?
is used as a pad for data
identifies the source address
identifies the destination address
marks the end of timing information
**is used for timing synchronization with alternating patterns of ones and zeros

10
What statements are true regarding addresses found at each layer of the OSI model? (Choose two.)
**Layer 2 may identify devices by a physical address burned into the network card
Layer 2 identifies the applications that are communicating
**Layer 3 represents a hierarchical addressing scheme
Layer 4 directs communication to the proper destination network
Layer 4 addresses are used by intermediary devices to forward data

11
Which statements describe the logical token-passing topology? (Choose two.)
Network usage is on a first come, first serve basis.
**Computers are allowed to transmit data only when they possess a token.
Data from a host is received by all other hosts.
**Electronic tokens are passed sequentially to each other.
Token passing networks have problems with high collision rates.

12
Which sublayer of the data link layer prepares a signal to be transmitted at the physical layer?
LLC
**MAC
HDLC
NIC

13
What is true regarding media access control? (Choose three.)
**Ethernet utilizes CSMA/CD
**defined as placement of data frames on the media
contention-based access is also known as deterministic
802.11 utilizes CSMA/CD
**Data Link layer protocols define the rules for access to different media
controlled access contains data collisions

14
What is a characteristic of a logical point-to-point topology?
The nodes are physically connected.
The physical arrangement of the nodes is restricted.
**The media access control protocol can be very simple.
The data link layer protocol used over the link requires a large frame header.

15
What two facts are true when a device is moved from one network or subnet to another? (Choose two.)
The Layer 2 address must be reassigned.
The default gateway address should not be changed.
**The device will still operate at the same Layer 2 address.
Applications and services will need additional port numbers assigned.
**The Layer 3 address must be reassigned to allow communications to the new network.



16
What is a function of the data link layer?
provides the formatting of data
provides end-to-end delivery of data between hosts
provides delivery of data between two applications
**provides for the exchange data over a common local media

17
Which three factors should be considered when implementing a Layer 2 protocol in a network? (Choose three.)
the Layer 3 protocol selected
**the geographic scope of the network
the PDU defined by the transport layer
**the physical layer implementation
**the number of hosts to be interconnected

18
What is the primary purpose of the trailer in a data link layer frame?
define the logical topology
provide media access control
**support frame error detection
carry routing information for the frame

19
A network administrator has been asked to provide a graphic representation of exactly where the company network wiring and equipment are located in the building. What is this type of drawing?
logical topology
**physical topology
cable path
wiring grid
access topology

20
Refer to the exhibit. Which statement describes the media access control methods that are used by the networks in the exhibit?
All three networks use CSMA/CA
None of the networks require media access control.
**Network 1 uses CSMA/CD and Network 3 uses CSMA/CA.
Network 1 uses CSMA/CA and Network 2 uses CSMA/CD.
Network 2 uses CSMA/CA and Network 3 uses CSMA/CD.

CCNA 1 - Module 6 (v4.0)

89,4%
1
How many bits make up an IPv4 address?

128
64
48
32 **


2
Refer to the exhibit. A network administrator has to develop an IP addressing scheme that uses the 192.168.1.0 /24 address space. The network that contains the serial link has already been addressed out of a separate range. Each network will be allocated the same number of host addresses. Which network mask will be appropriate to address the remaining networks?

255.255.255.248
255.255.255.224
255.255.255.192 **
255.255.255.240
255.255.255.128
255.255.255.252


3
Refer to the exhibit. The network administrator has assigned the internetwork of LBMISS an address range of 192.168.10.0. This address range has been subnetted using a /29 mask. In order to accommodate a new building, the technician has decided to use the fifth subnet for configuring the new network (subnet zero is the first subnet). By company policies, the router interface is always assigned the first usable host address and the workgroup server is given the last usable host address. Which configuration should be entered into the workgroup server's properties to allow connectivity to the network?

IP address: 192.168.10.38 subnet mask: 255.255.255.240 default gateway: 192.168.10.39
IP address: 192.168.10.38 subnet mask: 255.255.255.240 default gateway: 192.168.10.33
IP address: 192.168.10.38 subnet mask: 255.255.255.248 default gateway: 192.168.10.33 **
IP address: 192.168.10.39 subnet mask: 255.255.255.248 default gateway: 192.168.10.31
IP address: 192.168.10.254 subnet mask: 255.255.255.0 default gateway: 192.168.10.1


4
Refer to the exhibit. Which network prefix will work with the IP addressing scheme shown in the graphic.

/24
/16
/20
/27 **
/25
/28


5
Refer to the exhibit. A network administrator discovers that host A is having trouble with Internet connectivity, but the server farm has full connectivity. In addition, host A has full connectivity to the server farm. What is a possible cause of this problem?

The router has an incorrect gateway.
Host A has an overlapping network address.
Host A has an incorrect default gateway configured.
Host A has an incorrect subnet mask.
NAT is required for the host A network. **


6
What subnet mask would a network administrator assign to a network address of 172.30.1.0 if it were possible to have up to 254 hosts?

255.255.0.0
255.255.255.0 **
255.255.254.0
255.255.248.0


7
Given the IP address and subnet mask of 172.16.134.64 255.255.255.224, which of the following would describe this address?

This is a useable host address.
This is a broadcast address.
This is a network address. **
This is not a valid address.


8
What three facts are true about the network portion of an IPv4 address? (Choose three.)

identifies an individual device
is identical for all hosts in a broadcast domain
is altered as packet is forwarded **
varies in length **
is used to forward packets **
uses flat addressing


9
What is the network address of the host 172.25.67.99 /23 in binary?

10101100. 00011001.01000011.00000000
10101100. 00011001.01000011.11111111
10101100. 00011001.01000010.00000000 **
10101100. 00011001.01000010.01100011
10101100. 00010001.01000011. 01100010
10101100. 00011001.00000000.00000000


10
A router interface has been assigned an IP address of 172.16.192.166 with a mask of 255.255.255.248. To which subnet does the IP address belong?

172.16.0.0
172.16.192.0
172.16.192.128
172.16.192.160 **
172.16.192.168
172.16.192.176


11
Refer to the exhibit. Why would the response shown be displayed after issuing the command ping 127.0.0.1 on a PC?

The IP settings are not properly configured on the host. **
Internet Protocol is not properly installed on the host.
There is a problem at the physical or data link layer.
The default gateway device is not operating.
A router on the path to the destination host has gone down.


12
What two things will happen if a router receives an ICMP packet which has a TTL value of 1 and the destination host is several hops away? (Choose two.)

The router will discard the packet.
The router will decrement the TTL value and forward the packet to the next router on the path to the destination host.
The router will send a time exceeded message to the source host. **
The router will increment the TTL value and forward the packet to the next router on the path to the destination host.
The router will send an ICMP Redirect Message to the source host. **


13
Refer to the exhibit. An administrator is designing security rules for the 192.168.22.0 /24 network. Each security rule requires an address and mask pair to represent the machines that will be affected by the rule. Which two address and mask pairs will be the most precise way to reference the servers and hosts separately. (Choose two.)

192.168.22.40 255.255.255.248
192.168.22.40 255.255.255.252
192.168.22.100 255.255.255.128
192.168.22.100 255.255.255.254 **
192.168.22.1 255.255.255.192 **
192.168.22.101 255.255.255.224


14
Which of the following are features of IPv6? (Choose three.)

larger address space **
faster routing protocols
data types and classes of service **
authentication and encryption **
improved host naming conventions
same addressing scheme as IPv4


15
Which process do routers use to determine the subnet network address based upon a given IP address and subnet mask?

binary adding
hexadecimal anding
binary division
binary multiplication
binary ANDing **


16
What is the primary reason for development of IPv6?

security
header format simplification
expanded addressing capabilities **
addressing simplification


17
Which three IP addresses are private? (Choose three.)

172.168.33.1
10.35.66.70 **
192.168.99.5 **
172.18.88.90 **
192.33.55.89
172.35.16.5


18
Which statements are true regarding IP addressing? (Choose two.)

NAT translates public addresses to private addresses destined for the Internet.
Only one company is allowed to use a specific private network address space.
Private addresses are blocked from public Internet by router. **
Network 172.32.0.0 is part of the private address space.
IP address 127.0.0.1 can be used for a host to direct traffic to itself. **


19
Which IPv4 subnetted addresses represent valid host addresses? (Choose three.)

172.16.4.127 /26
172.16.4.155 /26 **
172.16.4.193 /26 **
172.16.4.95 /27
172.16.4.159 /27
172.16.4.207 /27 **


20
What is a group of hosts called that have identical bit patterns in the high order bits of their addresses?

an internet
a network **
an octet
a radi **


21
Refer to the exhibit. Host A is connected to the LAN, but it cannot get access to any resources on the Internet. The configuration of the host is shown in the exhibit. What could be the cause of the problem?

The host subnet mask is incorrect.
The default gateway is a network address.
The default gateway is a broadcast address.
The default gateway is on a different subnet from the host. **


22
Which of the following network devices are recommended to be assigned static IP addresses? (Choose three.)

LAN workstations
servers **
network printers **
routers **
remote workstations
laptops

89,4%

CCNA 1 - Module 5 (v4.0)

1
In an IPv4 environment, what information is used by the router to forward data packets from one interface of a router to another?
**destination network address
source network address
source MAC address
well known port destination address


2
What information is added during encapsulation at OSI Layer 3?
source and destination MAC
source and destination application protocol
source and destination port number
**source and destination IP address


3
In a connectionless system, which of the following is correct?
The destination is contacted before a packet is sent.
**The destination is not contacted before a packet is sent.
The destination sends an acknowledgement to the source that indicates the packet was received.
The destination sends an acknowledgement to the source that requests the next packet to be sent.


4
Which IP packet field will prevent endless loops?
type-of-service
identification
flags
**time-to-live
header checksum


5
Which portion of the network layer address does a router use to forward packets?
host portion
broadcast address
**network portion
gateway address


6
Refer to the exhibit. Using the network in the exhibit, what would be the default gateway address for host A in the 192.133.219.0 network?
192.135.250.1
192.31.7.1
192.133.219.0
**192.133.219.1


7
If the default gateway is configured incorrectly on the host, what is the impact on communications?
The host is unable to communicate on the local network.
**The host can communicate with other hosts on the local network, but is unable to communicate with hosts on remote networks.
The host can communicate with other hosts on remote networks, but is unable to communicate with hosts on the local network.
There is no impact on communications.


8
What is the purpose of a default gateway?
physically connects a computer to a network
provides a permanent address to a computer
identifies the network to which a computer is connected
identifies the logical address of a networked computer and uniquely identifies it to the rest of the network
**identifies the device that allows local network computers to communicate with devices on other networks


9
What type of routing uses information that is manually entered into the routing table?
dynamic
interior
**static
standard


10
When the destination network is not listed in the routing table of a Cisco router, what are two possible actions that the router might take? (Choose two.)
**The router sends an ARP request to determine the required next hop address.
The router discards the packet.
The router forwards the packet toward the next hop indicated in the ARP table.
**The router forwards the packet to the interface indicated by the source address.
The router forwards the packet out the interface indicated by the default route entry.


11
What are the key factors to consider when grouping hosts into a common network? (Choose three.)
**gateways
purpose
physical addressing
software version
**geographic location
**ownership


12
What is a component of a routing table entry?
the MAC address of the interface of the router
the destination Layer 4 port number
the destination host address
**the next-hop address


13
Which intermediary devices could be used to implement security between networks? (Choose two.)
**router
hub
switch
**firewall
access point
bridge


14
What are three common problems with a large network? (Choose three.)
too few broadcasts
**performance degradation
**security issues
**limited management responsibility
host identification
protocol compatibility


15
Refer to the exhibit. All devices shown in the exhibit have factory default settings. How many broadcast domains are represented in the topology that is shown?
3
**4
5
7
8
11


16
Which three statements are true about routes and their use? (Choose three.)
If no route to the destination network is found, the packet is returned to the previous router.
If the destination network is directly connected, the router forwards the packet to the destination host.
**If multiple network entries exist for the destination network, the most general route is used to forward the packet.
**If no route exists for the destination network and a default route is present, the packet is forwarded to the next-hop router.
**If the originating host has a default gateway configured, the packet for a remote network can be forwarded using that route.
If a host does not have a route manually configured for the destination network, the host will drop the packet.


17
Refer to the exhibit. A network administrator is troubleshooting a connectivity problem and needs to determine the address that is used to forward network packets out the network. Using the netstat -r command, the administrator would identify which address as the address to which all hosts send packets that are destined for an outside network?
10.10.10.26
127.0.0.1
**10.10.10.6
10.10.10.1
224.0.0.0


18
Refer to the exhibit. A network administrator notices that there are too many broadcasts on the network. What two steps can the network administrator take to resolve this problem? (Choose two.)
**Replace S2 with a router.
Place all servers on S1.
Disable TCP/IP broadcasts.
**Subnet the 192.168.0.0 /24 network.
Disable all unused interfaces on the switches.


19
Refer to the exhibit. The network in the exhibit is fully operational. What two statements correctly describe the routing for the topology that is shown? (Choose two.)
**192.168.0.2 is the next-hop address that is used by R3 to route a packet from the 10.0.0.0 network to the 172.16.0.0 network.
10.0.0.1 is the next-hop address that is used by R1 to route a packet from the 192.168.12.0 network to the 10.0.0.0 network.
**192.168.0.1 is the next-hop address that is used by R1 to route a packet from the 192.168.12.0 network to the 172.16.0.0 network.
172.16.0.1 is the next-hop address that is used by R3 to route a packet from the 10.0.0.0 to the 172.16.0.0 network.
192.168.0.1 is the next-hop address that is used by R2 to route a packet from the 172.16.0.0 network to the 192.168.12.0 network.
192.168.0.2 is the next-hop address that is used by R2 to route a packet from the 172.16.0.0 network to the 192.168.12.0 network.


20
What two characteristics are commonly associated with dynamic routing protocols? (Choose two.)
require no device configuration
**provide routers with up-to-date routing tables
require less processing power than static routes require
consume bandwidth to exchange route information
**prevent manual configuration and maintenance of the routing table


21
What statement describes the purpose of a default route?
A host uses a default route to transfer data to another host on the same network segment.
A host uses a default route to forward data to the local switch as the next hop to all destinations.
A host uses a default route to identify the Layer 2 address of an end device on the local network.
**A host uses a default route to transfer data to a host outside the local network when no other route to the destination exists.

CCNA 1 - Module 4 (v4.0)

1
Refer to the exhibit. What two pieces of information can be determined from the output that is shown? (Choose two.)
The local host is using well-known port numbers to identify the source ports.
**A termination request has been sent to 192.135.250.10.
Communication with 64.100.173.42 is using HTTP Secure.
**The local computer is accepting HTTP requests.
192.168.1.101:1042 is performing the three-way handshake with 128.107.229.50:80.


2
After a web browser makes a request to a web server that is listening to the standard port, what will be the source port number in the TCP header of the response from the server?
13
53
**80
1024
1728


3
Which information is found in both the TCP and UDP header information?
sequencing
flow control
**acknowledgments
source and destination


4
Which is an important characteristic of UDP?
acknowledgement of data delivery
**minimal delays in data delivery
high reliability of data delivery
same order data delivery


5
Refer to the exhibit. Host A is using FTP to download a large file from Server 1. During the download process, Server 1 does not receive an acknowledgment from Host A for several bytes of transferred data. What action will Server 1 take as a result?
create a Layer 1 jam signal
**reach a timeout and resend the data that needs to be acknowledged
send a RESET bit to the host
change the window size in the Layer 4 header


6
Refer to the exhibit. In line 7 of this Wireshark capture, what TCP operation is being performed?
**session establishment
segment retransmit
data transfer
session disconnect


7
Refer to the exhibit. The initial TCP exchange of data between two hosts is shown in the exhibit. Assuming an initial sequence number of 0, what sequence number will be included in Acknowledgment 2 if Segment 6 is lost?
2
3
6
**1850
3431
3475


8
Why is flow control used for TCP data transfer?
to synchronize equipment speed for sent data
to synchronize and order sequence numbers so data is sent in complete numerical order
**to prevent the receiver from being overwhelmed by incoming data
to synchronize window size on the server
to simplify data transfer to multiple hosts


9
During a TCP communication session, if the packets arrive to the destination out of order, what will happen to the original message?
The packets will not be delivered.
The packets will be retransmitted from the source.
**The packets will be delivered and reassembled at the destination.
The packets will be delivered and not reassembled at the destination.


10
With TCP/IP data encapsulation, which range of port numbers identifies all well-known applications?
0 to 255
256 to 1022
**0 to 1023
1024 to 2047
49153 to 65535


11
Which transport layer protocol provides low overhead and would be used for applications which do not require reliable data delivery?
TCP
IP
**UDP
HTTP
DNS


12
What are two features of the User Datagram Protocol (UDP)? (Choose two.)
**flow control
**low overhead
connectionless
connection-oriented
sequence and acknowledgements


13
What mechanism is used by TCP to provide flow control as segments travel from source to destination?
sequence numbers
session establishment
**window size
acknowledgments


14
What is dynamically selected by the source host when forwarding data?
destination logical address
source physical address
default gateway address
**source port


15
Why are port numbers included in the TCP header of a segment?
to indicate the correct router interface that should be used to forward a segment
to identify which switch ports should receive or forward the segment
to determine which Layer 3 protocol should be used to encapsulate the data
**to enable a receiving host to forward the data to the appropriate application
to allow the receiving host to assemble the packet in the proper order


16
Which two options represent Layer 4 addressing? (Choose two.)
identifies the destination network
**identifies source and destination hosts
identifies the communicating applications
**identifies multiple conversations between the hosts
identifies the devices communicating over the local media


17
Which three features allow TCP to reliably and accurately track the transmission of data from source to destination?
**encapsulation
flow control
connectionless services
**session establishment
**numbering and sequencing
best effort delivery


18
Which OSI model layer is responsible for regulating the flow of information from source to destination, reliably and accurately?
application
presentation
session
**transport
network


19
Based on the transport layer header shown in the diagram, which of the following statements describe the established session? (Choose two.)
This is a UDP header.
**This contains a Telnet request.
This contains a TFTP data transfer.
The return packet from this remote host will have an Acknowledgement Number of 43693.
**This is a TCP header.


20
Which event occurs during the transport layer three-way handshake?
The two applications exchange data.
TCP initializes the sequence numbers for the sessions.
**UDP establishes the maximum number of bytes to be sent.
The server acknowledges the bytes of data received from the client.

CCNA 1 - Module 3 (v4.0)

1.
What is the purpose of resource records in DNS?
used by the server to resolve names




2.
What are two forms of application layer software?
applications
syntax


3.
What application layer protocol is commonly used to support for file transfers between a client and a server?
FTP


4.
What are two characteristics of peer-to-peer networks?
decentralized resources
resource sharing without a dedicated server


5.
Which layer of the OSI model supplies services that allow user to interface with the network?
application


6.
What are three properties of peer-to-peer applications?
acts as both a client and server within the same communication
hybrid mode includes a centralized directory of files
does not require specialized software


7.
What is the role of the OSI application layer?
provides the interface between the applications on either end of the network


8.
What three protocols operate at the Application layer of the OSI model?
DNS, SMTP, POP


9.
Which email components are used to forward mail between servers?
MDA, MTA


10.
Which two protocols are used to control the transfer of web resources from a web server to a client browser?
HTTPS
HTTP


11.
Which statements are correct concerning the role of the MTA in handling email?
receives email from the client's MUA
passes email to the MDA for final delivery
uses SMTP to route email between servers


12.
As compared to SSH, what is the primary disadvantage of telnet?
does not support encryption


13.
Which application layer protocols correctly match a corresponding function?
DNS dynamically allocates IP addresses to hosts
Telnet provides a virtual connection for remote access


14.
What is the automated service that matches resource names with the required IP address?
DNS


15.
Refer to the exhibit. What is the destination port for the communication that is represented on line 5?
80


16.
What are two characteristics of clients in data networks?
initiate data exchanges
may upload data to servers


17.
What application layer protocol describes the services that are used for file sharing in Microsoft networks?
SMB


18.
A network administrator is designing a network for a new branch office of twenty-five users. What are the advantages of using a client-server model?
centralized administration
security is easier to enforce


19.
A small home network has been installed to interconnect three computers together for gaming and file sharing. What two properties represent this network type?
User accounts are centralized.
Security is difficult to enforce.


20.
How does the application layer on a server usually process multiple client request for services?
uses support from lower layer functions to distinguish between connections to th